Yes, a trailer tire may need replacing even if it still has plenty of tread. Tire maker Carlstar states that remaining tread does not indicate a trailer tire's service life, and Michelin recommends replacing its tires ten years after the date of manufacture, regardless of how they look. To decide, check the tire's age using the DOT code, the condition of the sidewalls, the cold inflation pressure and your trailer's actual load.

In short

  • The date of manufacture is usually found in the last four digits of the DOT code: the week, then the year.
  • Michelin recommends a yearly inspection by a professional after five years of use and replacement ten years after manufacture, spare tire included.
  • According to Carlstar, a trailer left parked under load for a long time can have tires that are degraded inside, with no visible sign.
  • Inflate to the pressure specified by the trailer manufacturer, never to the maximum pressure moulded on the sidewall.
  • Any cracked or bulging tire should be assessed by a professional before going back on the road.

Why replace a trailer tire that still has tread?

On a car, tires are usually replaced because they are worn out. A trailer, on the other hand, sees little mileage: a few trips to the cottage, a move, launching the boat. Its tires often age long before they wear out.

Carlstar, which makes Carlisle trailer tires, is clear: irregular use and prolonged storage under a static load, often without movement or maintenance, can degrade the casing, meaning the tire's internal structure. This damage cannot be detected by a visual inspection. A tire that still looks good is not necessarily a tire in good condition.

How do I read the DOT code to find a tire's age?

Canada's Motor Vehicle Tire Safety Regulations (SOR/2013-198) require the tire identification number to include four symbols that indicate the date of manufacture. Here is how to find and read them.

  1. Find the letters DOT on the sidewall. They are followed by a series of letters and numbers moulded into the rubber.
  2. Locate the last group of four digits. According to Carlstar, the date code is usually at the end of the DOT identification.
  3. Read the first two digits: that is the week. Under the regulations, the week beginning on the first Sunday of the year is numbered 01, the next one 02, and so on.
  4. Read the last two digits: that is the year. They are the last two digits of the year in which that week begins.

Carlstar's example: the code 3409 means the tire was made in the 34th week of 2009. Under the recommendation Michelin gives for its own tires, a tire of that age would have been due for replacement by 2019, even if it had hardly been driven. For a tire of another brand, check that manufacturer's own guidance.

For the rest of the markings (size, load index, ST designation), see our article on reading the sidewall of an ST trailer tire.

At what age should a trailer tire be replaced?

There is no single age that applies to every tire: what counts is the guidance from your tires' manufacturer. Here is what two of them say.

  • Michelin recommends that after five years of use, tires be thoroughly inspected at least once a year by a tire professional.
  • Michelin also recommends, as a precaution, replacing tires ten years after their date of manufacture, regardless of remaining tread or appearance.
  • Carlstar points out that remaining tread does not indicate a trailer tire's service life.

Are your tires another brand, such as Goodyear Endurance or Bridgestone? Check that manufacturer's maintenance guide, which is the reference for its products. When in doubt, an inspection by a professional remains the most cautious way to decide.

My trailer tire is cracked: is it still safe?

No one can answer that question remotely, and a photo is not enough. Carlstar stresses this point: a tire can be degraded inside without it showing, and Michelin recommends replacing tires at ten years, even if they look fine.

If you notice cracks on the sidewalls or in the tread grooves, do not rely on your own judgment. Have the tire examined by a professional before hitting the road, especially if it is approaching or past five years of use.

What pressure should I put in a trailer tire?

The recommended pressure, not the maximum pressure

According to Transport Canada, the maximum pressure moulded on the sidewall is the pressure needed for the tire to carry its maximum load; it is generally not the pressure recommended by the vehicle manufacturer. So do not inflate to that number. Use the pressure specified by the trailer manufacturer on the trailer's tire information label instead.

If that label is unreadable or missing, contact the trailer manufacturer or have a professional confirm the appropriate pressure.

Measure cold, at least once a month

Transport Canada recommends checking pressure at least once a month with a good gauge, when the tires are cold. Before a trip, take the reading before you drive, not after a few kilometres.

Worked example: pressure lost during off-season storage

The TP 2823 brochure distributed by the Tire and Rubber Association of Canada states that a tire loses about 14 kPa (2 psi) per month through permeation, and about 7 kPa (1 psi) for every 5 °C drop in temperature. Picture a trailer inflated on a warm September day, then checked five months later on a morning that is 20 °C colder.

Permeation will have taken away about 70 kPa (10 psi) and the cold about 28 kPa (4 psi), for a total of nearly 100 kPa (14 psi) less. It is a ballpark figure to confirm with a gauge, but it shows clearly why you should measure before every outing.

Is my trailer too heavily loaded for its tires?

Transport Canada specifies that the tire information label shows the maximum recommended load. Compare that figure with the actual weight of the loaded trailer: boat and motor, snowmobiles, ATVs, materials, not to mention the extra gear tossed in "while we're at it."

If the actual weight is close to or above the maximum recommended load, lighten the load or ask for advice before driving. When it is time to replace your tires, choose a size and load index that meet your trailer's requirements.

My trailer sat all winter: what should I check?

It is a common situation: the trailer waits for warmer weather in the driveway or at the back of the yard. According to Carlstar, prolonged storage under a static load, without movement or maintenance, can degrade the casing without any visible sign.

Before the first outing, go over each tire carefully, spare included. Check the DOT date, inflate cold according to the trailer's label and look for any bulge, deformation or cracking. For next winter, reducing the load on the tires, for example by emptying the trailer, is in line with Carlstar's warnings.

The pre-season checklist

  • Age: read the DOT code on each tire and note the week and year of manufacture.
  • Sidewalls: look for cracks, cuts, deep scuffs or exposed cords.
  • Bulges: run your hand over the sidewalls and tread; a bump or deformation is a stop sign.
  • Uneven wear: compare wear in the centre and on the edges, then from one tire to the other.
  • Cold pressure: measure with a good gauge and adjust to the trailer's tire information label.
  • Actual load: compare the weight of your usual load with the maximum recommended load on the information label.
  • Spare tire: check its date, pressure and condition; according to Michelin, it ages whether it has been used or not.

Which sign calls for which action?

SignRiskWhat to do
DOT code more than ten years oldAging that may not be visibleReplace per Michelin's recommendation for its tires; check your own tire manufacturer's guidance
More than five years of useDegradation that is hard to judge yourselfThorough inspection by a professional at least once a year (Michelin)
Cracks on the sidewall or treadTrue condition impossible to confirm by eyeHave it assessed by a professional before driving
Bump or bulgePossible damage to the internal structureDo not drive on this tire; have it inspected
Uneven wearCause needs to be diagnosedHave the whole setup checked by a professional
Pressure below the label valueTire underinflated for its loadInflate cold according to the label; check monthly
Actual load close to or above the maximum recommended loadPossible tire overloadLighten the load or ask for advice before driving
Old or flat spare tireSpare unusable when you need itCheck its date and pressure; apply the same age criteria

Advice from our shop

Take a photo of the DOT code on each tire, spare included, and keep those photos on your phone along with the pressure shown on the trailer's label. In the spring, you will know in seconds whether a tire is nearing the age at which its manufacturer recommends an inspection or replacement. And if a tire makes you hesitate, do not keep it "for one last season": have it assessed before you load the trailer.

When you replace an aged tire, also check the date on the other tire on the same axle. It may be the same age and have gone through the same storage conditions.

What should I do now?

A trailer tire should be judged first by its age, condition and conditions of use, well before its tread. Read the DOT code, inflate cold according to the trailer's label, compare the actual load with the maximum recommended load and have any cracked or bulging tire assessed.

If you need replacements, browse our trailer tires online: the current price is shown on each catalogue listing. We deliver across Quebec; lead times are explained on our tire delivery page.

Want them installed? Installation is done only at our Laval shop, at 1870 rue Cunard, at the earliest four business days after the order for ordered tires. It is offered for light vehicles only: no 16.5-inch wheels and no industrial vehicles. Book your time slot online or, for a question about your trailer, reach our team at 450-256-1685.

Ready to buy

Ready to order your tires?

Compare the tires available in your size, order online and choose delivery or installation at our Laval shop.

  • Free, fast delivery in Quebec when you buy 4 eligible tires or wheels
  • Installation by appointment on Saturdays, 9 a.m. to 4 p.m., until November 28

FAQ

Frequently asked questions

How many years does a trailer tire last?

There is no single lifespan: it depends on use, storage and your tire manufacturer's guidance. For its tires, Michelin recommends a yearly professional inspection after five years of use and replacement ten years after the date of manufacture. Carlstar points out that remaining tread is not a good indicator of service life.

Where is the manufacturing date on a trailer tire?

It is part of the identification number that follows the letters DOT on the sidewall, usually at the end, as four digits. The first two give the week and the last two give the year. For example, 2218 means the 22nd week of 2018.

Can I inflate my trailer tires to the maximum pressure on the sidewall?

No. According to Transport Canada, that number is the pressure needed to carry the tire's maximum load and is generally not the recommended pressure. Follow the pressure specified by the trailer manufacturer on the tire information label, measured when the tires are cold.

Is a spare tire that has never been used still as good as new?

Not necessarily. Michelin states that a spare tire ages whether it has been used or not, and its recommendation to replace tires ten years after manufacture applies to the spare too. Check its DOT date, pressure and condition at the start of every season.

Where can I get trailer tires installed in Laval?

Installation is done only at the Liqui Pneus shop, 1870 rue Cunard in Laval, by appointment booked online, and for light vehicles only: no 16.5-inch wheels and no industrial vehicles. For ordered tires, it is possible at the earliest four business days after the order. If you are unsure about your trailer, call 450-256-1685.